Skip to content

Bhuttu

Forum Replies Created

Viewing 13 posts - 1 through 13 (of 13 total)
  • Author
    Posts
  • October 1, 2020 at 3:14 pm in reply to: Interfacial nodes in shan/chen or free energy model #5200
    Bhuttu
    Participant

    Sure, I will share the code.

    Sincerely
    Bhuttu

    October 1, 2020 at 8:50 am in reply to: Interfacial nodes in shan/chen or free energy model #5195
    Bhuttu
    Participant

    Thank you Mathias.
    Will try this.

    Regards
    Bhuttu

    October 1, 2020 at 5:02 am in reply to: Interfacial nodes in shan/chen or free energy model #5193
    Bhuttu
    Participant

    Thank you for the response Mathias.
    Will it work if I track the value of density throughout the cells?
    I am asking this question because as far as I understand there is no sharp change in the density values and there is a finite distance associated where this change happens.

    Thanks and regards
    Bhuttu

    October 1, 2020 at 4:51 am in reply to: I can’t run bstep2d #5192
    Bhuttu
    Participant

    Hello Souhaila,
    As I can see in the second image that you posted, the first file is the executable file. Now in the terminal just type ./bstep2d and it will execute this file and you should get some output on your terminal.

    Best
    Bhuttu

    September 21, 2020 at 3:13 am in reply to: ContactAngle2d.cpp Singular Point #5148
    Bhuttu
    Participant

    Thank you Sam. I will read the paper and will try to understand the approach followed in it.
    Thank you.

    Best regards
    Bhuttu

    September 18, 2020 at 9:50 am in reply to: Warning message in bstep2d.cpp #5141
    Bhuttu
    Participant

    Hello Max,
    Thanks for inviting me! I will surely try if I can arrange everything for spring school. Is there anything that I can attend online?

    Thanks and regards
    Bhuttu

    September 18, 2020 at 8:45 am in reply to: Warning message in bstep2d.cpp #5138
    Bhuttu
    Participant

    Thanks Max
    Could you please tell me what is that noOfCuboids term used in the same code?

    Regards
    Bhuttu

    September 16, 2020 at 12:25 pm in reply to: ContactAngle2d.cpp #5128
    Bhuttu
    Participant

    Thank you Sam 🙂 🙂
    Sorry for the late reply I was busy in something.
    Yes I got where I was wrong.

    Regards
    Bhuttu

    August 23, 2020 at 11:38 am in reply to: Compressible LBM #5108
    Bhuttu
    Participant

    Hello Mathias
    Please suggest me a good source to study about the error norms. It will be really helpful for me.

    Thanks and regards
    Bhuttu

    July 12, 2020 at 3:10 am in reply to: Poiseuille2d #5061
    Bhuttu
    Participant

    Ok. Thank you Mathias 🙂

    July 11, 2020 at 5:21 am in reply to: Poiseuille2d #5058
    Bhuttu
    Participant

    Thank you Mathias for your response!
    Can you please give me some idea on how to deal with corners. If I use any of the two available boundary conditions like here in this case you used No-Slip and avoided using PBC. Results should not be significantly different if my system size is large enough?
    Thanks a lot.

    Regards
    Bhuttu

    May 29, 2020 at 2:30 pm in reply to: Temperature effect on surface tension #5002
    Bhuttu
    Participant

    Hello max,
    Thank you for your suggestion will try this soon. I will definitely like to report back my findings and also some doubts, as I go into the topic.

    Sincerely,
    Bhuttu

    May 19, 2020 at 5:13 pm in reply to: Writing sequential code #4961
    Bhuttu
    Participant

    Thank you Mathias.
    I will definitely try to understand cavity2d example and will also like to come in spring school if my institute permits me.

    Regards,
    Bhuttu

  • Author
    Posts
Viewing 13 posts - 1 through 13 (of 13 total)